Browsing Texas A&M Engineering Experiment Station by Title
Now showing items 4653-4672 of 8496
-
(Turbomachinery Laboratory, Texas A&M Engineering Experiment Station, 2022)This study starts by presenting a typical ethylene plant which will act as the ‘base plant’ for this case study. Then, a ‘low�emission’ ethylene plant is introduced which employs a new cracker technology having ...
-
(Turbomachinery Laboratory, Texas A&M Engineering Experiment Station, 2017)
-
(Energy Systems Laboratory (http://esl.tamu.edu); Texas A&M University (http://www.tamu.edu), 2006)This paper sets up a mathematical model of three-dimensional steady turbulence heat transfer in an air-conditioned room of multi-polluting heat sources. Numerical simulation helps identify key factors in displacement ...
-
(Mary Kay O'Connor Process Safety Center; Texas &M University. Libraries, 2017)United States Chemical Safety and Hazard Investigations Board
-
(2007)
-
(Energy Systems Laboratory (http://esl.eslwin.tamu.edu), 1993-03)The needs of electricity consumers along with the utility industry are rapidly changing. Consumers want electricity to perform more functions, improve efficiencies and help lower the cost of production, all in an environmentally ...
-
(Energy Systems Laboratory (http://esl.tamu.edu); Texas A&M University (http://www.tamu.edu), 1981)In a typical furniture factory, up to 70% of all incoming lumber ends up as useless waste. Though burnable, its enormous volume far exceeds the fuel needs of the plant's steam supply system. The excess must go to scarce, ...
-
(Turbomachinery Laboratory, Texas A&M Engineering Experiment Station, 2018)Not accounting for detrimental environment factors in the design and environment degradation are two of the most common causes of Turbomachinery component failures. This paper discusses the importance of knowing the operating ...
-
(Texas A&M University. Turbomachinery Laboratories, 2009)Condition monitoring data collection capabilities have grown over the last decade in large part due to advances in integrated circuits (IC). These advances now permit real time thermodynamic and process calculations on ...
-
(Turbomachinery Laboratory, Texas A&M Engineering Experiment Station, 2021)The paper examines the case of a rotordynamic analysis and subsequent rotodynamic testing conducted during the pre-order phase for a five-stage integrally-geared centrifugal compressor, which today is operating in a refinery ...
-
(Turbomachinery Laboratory, Texas A&M Engineering Experiment Station, 2021)Acceptance criteria for high-speed balancing of turbomachinery are specified in API standards based on either pedestal velocity or shaft displacement, and these are discussed in detail Pedestal velocities are measured using ...
-
(Turbomachinery Laboratory, Texas A&M Engineering Experiment Station, 2021)A re-examination of the well-known Ekofisk re-injection centrifugal compressor is presented Several opportunities makethis an ideal candidate to assess how well (or not) current design and analytical methods have evolved ...
-
(Turbomachinery Laboratory, Texas A&M Engineering Experiment Station, 2021)Test results are presented and compared for the following annular pump seal geometries: (a) a smooth-rotor/circumferentially-grooved stator (SR/GS) and (b) a smooth-stator/circumferentially-grooved rotor (GR/SS) The GR/SS ...
-
(Turbomachinery Laboratory, Texas A&M Engineering Experiment Station, 2021)This paper will explore the development of a new annular sealwear component design for use in centrifugal pumps Thedesign uses a pattern of holes (or perforations) machinedthrough a composite material wear component The ...
-
(Turbomachinery Laboratory, Texas A&M Engineering Experiment Station, 2021)In the turbomachinery applications, the geared transmission equipment are among the most affected bythe lube oil characteristics and properties In a gear system the oil is used in the fluid-dynamic bearings,journal and ...
-
(Turbomachinery Laboratory, Texas A&M Engineering Experiment Station, 2021)Standard centrifugal compressors (CC) are designed to process dry gas or gas mixed with negligible amount of liquid Significantliquid content, namely liquid mass fraction (LMF) up to 30%, yield to rapid mechanical deterioration ...
-
L09: Development and Application of Very High Flow Coverd Stages for Process Centrifugal Compressors (Turbomachinery Laboratory, Texas A&M Engineering Experiment Station, 2021)The present work describes the development and application of a family of very high flow (VHF) stages with nominal design flow coefficient of 024 and moderate to high Machine Mach Number (Mu) of 088 The design is essentially ...
-
(Turbomachinery Laboratory, Texas A&M Engineering Experiment Station, 2021)Acoustic resonance can develop within the hydraulic channels of the pump, especially in the long crossover channel of a multistagecentrifugal pump This phenomenon occurs when the hydraulic channel length is equal to the ...
-
(Turbomachinery Laboratory, Texas A&M Engineering Experiment Station, 2021)Many gas compressor stations use multiple gas turbine driven centrifugal compressors and the units may not beidentical For connected systems, such as pipelines, or gas field operations, compressors of several compressorstations, ...
-
(Turbomachinery Laboratory, Texas A&M Engineering Experiment Station; Texas A & M University. Libraries; Texas A & M University. Libraries, 2021)In the last few years, the installed capacity and production of electricity from all the renewable energies have significantly risen, supported by an ever-increasing spread of new energy policies all around the world. ...