Browsing by Title
Now showing items 54684-54703 of 121333
-
(Texas A&M University. Libraries, 1993)Heat transfer in a two-dimensional serpentine channel with a series of right angle turns was investigated experimentally and numerically. Similar channel geometry can be found typically in heat exchangers, thermal regenerators, ...
-
(Texas A&M University, 1973)Not available
-
(2009-05-15)The gas turbine blade/vane internal cooling is achieved by circulating the compressed air through the cooling passages inside the turbine blade. Leading edge and trailing edge of the turbine blade are two critical regions ...
-
(Turbomachinery Laboratories, Department of Mechanical Engineering, Texas A&M University, 1989)Numerous studies have shown that mechanical seal reliability is related to the state of the fluid between the seal faces. In turn, the fluid state depends on the seal face temperature. Unfortunately, calculating the seal ...
-
(2011-08-03)Gas turbine blade/vane cooling is obtained by circulating the high pressure air from compressor to the internal cooling passage of the blade/vane. Heat transfer and cooling effect in the rotating blade is highly affected ...
-
(Texas A&M University, 2003)An experimental study was performed to measure the regionally averaged heat transfer distributions in a rotating ribbed channel with an aspect ratio of 4:1. The Reynolds number, based on a hydraulic diameter, varies from ...
-
(2010-01-16)Cooling channels with a developing flow entrance condition and aspect ratios of 1:4 and 2:1 were studied. The range of the rotation number and buoyancy parameter for the selected AR channels was extended. The maximum Ro ...
-
(Texas A&M University, 1989)Not available
-
(Texas A&M University, 2000)In this research air flow transient heat transfer in a two-pass channel via thermochromic liquid crystals is studied. An 180° turn and rib roughened surface are part of the channel. This geometric combination simulates ...
-
(2014-07-08)Heat transfer modeling is important in many fields of engineering. In petroleum engineering, heat transfer modeling has many applications. One such application that this study focused on is flow rate estimation. In this ...
-
(Mary Kay O'Connor Process Safety Center; Texas &M University. Libraries, 2018)The consumption of natural gas is expected to increase significantly over the next few decades due to much less carbon dioxide emission per unit of energy, when compared to other sources like oil or coal. This has also ...
-
(2012-02-14)The present study has focused on the use of coil heat exchangers (CHEs) with microencapsulated phase change material (MPCM) slurries to understand if CHEs can yield greater rates of heat transfer. An experimental study was ...
-
Heat Transfer Performance and Piping Strategy Study for Chilled Water Systems at Low Cooling Loads (2012-12-05)The temperature differential of chilled water is an important factor used for evaluating the performance of a chilled water system. A low delta-T may increase the pumping energy consumption and increase the chiller energy ...
-
(Energy Systems Laboratory (http://esl.tamu.edu); Texas A&M University (http://www.tamu.edu), 1981)This paper describes an EPRI-funded experimental evaluation of advanced air-cooled ammonia condensers for a phase. Change dry/wet cooling system for power plants. Two condenser surfaces with different air-side augmentation ...
-
(Texas A&M University, 1951)
-
(Digital: Cushing Memorial Library and Archives, Texas A&M University, College Station, Texas; Physical: Graphic Services, Texas A&M University, 2011-08-17)
-
(Digital: Cushing Memorial Library and Archives, Texas A&M University, College Station, Texas; Physical: Graphic Services, Texas A&M University, 2011-08-17)
-
(2013-08-08)As one of the most attractive reactor types, The High Temperature Gas-cooled Reactor (HTGR) is designed to be passively safe with the incorporation of Reactor Cavity Cooling System (RCCS). In this paper, a RELAP5-3D ...
-
(2014-05-08)The heat transfer behaviors of non-Newtonian fluids under laminar flow conditions in circular tubes are presented in this study. The constant wall heat flux is considered as a boundary condition for dilute polymer solutions ...
-
(Energy Systems Laboratory (http://esl.tamu.edu); Texas A&M University (http://www.tamu.edu), 1984)Almost every industrial process needs some form of cooling. Water is still the most extensively used fluid for cooling, but the days when plenty of it was available are gone forever. Water conservation is currently achieved ...